OFS06 Infrared Sauna Application Guide: Hotel, Guesthouse & Spa
OFS06 Infrared Sauna Application Guide: Hotel, Guesthouse & Spa

This guide maps the OFS06A-5 and OFS06B infrared sauna room series to hotel and hospitality, guesthouse, wellness and commercial club, and spa facilities. It explains how to use documented model power ratings, far infrared heating plates, AV1 control and shared features such as hemlock, aspen and red cedar construction, tempered glass, colorful lighting, FM/Bluetooth/USB and two speakers when specifying a sauna room for a project.
OFS06A-5 is included in this application guide. Its individual wattage should be confirmed on the model datasheet before circuit design; this guide does not assign a rating that is not in the published model specification. The documented reference models used here are OFS06A-1 at 1,200W, OFS06A-3-1 at 1,600W, OFS06B-2 at 1,850W and OFS06B-4 at 2,300W. The documented OFS06C outdoor models are OFS06C-4 at 2,300W and OFS06C-3-2 at 2,500W.
OCEAN FUTURE is the manufacturer and supplier referenced in this guide. The company states a 50,000 m2 factory, 200+ employees, 5,000 sets annual output, 9 engineers, an 85% export ratio and markets including the USA, Australia, the EU and Germany. Its official website is OCEAN FUTURE official website.
The specification problem: model fit, not a generic sauna claim
A hotel, guesthouse or spa does not need a generic claim that one sauna room is best for every project. It needs a model that matches the installation location, electrical schedule, guest interface, compliance review and purchasing terms. The OFS06 platform has several documented configurations, and the differences that matter are specific: total power, far infrared heating plate or plate plus box, AV1 control, painted surface or outdoor pentroof construction, and shared media and lighting features.
Confusing these variables can cause a late electrical upgrade, a control layout that does not fit the operating routine, or a model specified for the wrong installation condition. The application record is clear that sauna rooms can operate under indoor or outdoor installation conditions, in high-temperature and variable climate environments including sun exposure, rain and low temperature, and in corrosion-resistant conditions. It is not enough to choose a wood finish and a power number; the project must confirm the installation condition, the safety requirements and the exact model record.
The application requirements also list heat-resistant and non-toxic materials, waterproof and moisture-proof construction, overheat protection, low EMF for infrared models, UV resistance for outdoor models, durable thermal insulation, and use with a control panel and safety thermometer. These are specification items to verify, not claims that every model automatically includes every item. The buyer should keep them in the acceptance checklist beside the model nameplate and the electrical schedule.
Industry background: separate room compliance from electrical compliance
Sauna rooms are specified in hospitality and wellness projects as amenity spaces, but the compliance object is not a single item. According to a secondary industry report, EN 18164 was published in February 2026 and covers the design and construction of sauna rooms, warm-air rooms, steam rooms and soft steam rooms in public facilities in Europe. The same report states that UL 60335-2-53 for electric sauna heaters was published in June 2025 in the US. These references support a practical split: review room construction and the electrical or heater subsystem separately, and confirm model-specific documentation for the destination market.
This is also why an application guide should not treat a series power range as a model rating. The OFS06 records show different total power values across models, and the heater record differs between far infrared heating plate and far infrared heating plate plus box. Those are specification facts, not proof that one configuration is better for every project. The buyer should match them to the project's electrical capacity, installation condition and guest-facing requirements.
For hotel and spa projects, the operating model also matters. AV1 control, FM/Bluetooth/USB, two speakers, lamp and colorful light are listed on the documented OFS06 models. These features affect the guest-facing specification and the handover checklist. They do not replace the need to confirm heating layout, safety documents and the exact power supply for the selected model.
What the OFS06 platform provides
Across the documented OFS06A, OFS06B and OFS06C records, the common control and guest-facing specification includes AV1 control, FM/Bluetooth/USB, two speakers, lamp, colorful light, wood handle and tempered glass. Materials listed are hemlock, aspen and red cedar. Applicable industries are hotel and hospitality, guesthouse, wellness and commercial club, and spa facilities. The records distinguish indoor infrared models from outdoor models with an outdoor pentroof; they also distinguish a painted surface from an outdoor pentroof construction. These are the common facts to carry into a project specification.

| Model | Type | Total power | Heater record | Control | Shared features | Planning note |
|---|---|---|---|---|---|---|
| OFS06A-1 | Infrared sauna room | 1,200W | Far infrared heating plate | AV1 | FM/Bluetooth/USB, two speakers, lamp, colorful light, wood handle, tempered glass; painted surface | Lowest documented OFS06A power in this set; confirm circuit and room load. |
| OFS06A-3-1 | Infrared sauna room | 1,600W | Far infrared heating plate | AV1 | Same shared feature set; painted surface | Low-power reference for guesthouse or limited-load projects after electrical check. |
| OFS06B-2 | Infrared sauna room | 1,850W | Far infrared heating plate + box | AV1 | Same shared feature set; painted surface | Documented B-series step between the A models and OFS06B-4. |
| OFS06B-4 | Infrared sauna room | 2,300W | Far infrared heating plate + box | AV1 | Same shared feature set; painted surface | Higher documented B-series power; confirm circuit and installation. |
| OFS06C-4 | Outdoor sauna room | 2,300W | Far infrared heating plate + box | AV1 | Shared feature set; outdoor pentroof | Outdoor variant; pentroof listed. Do not treat A/B models as weatherproof by default. |
| OFS06C-3-2 | Outdoor sauna room | 2,500W | Far infrared heating plate + box | AV1 | Shared feature set; outdoor pentroof | Outdoor variant with higher documented power than OFS06C-4. |
OFS06A-5 is part of this application guide. Its individual wattage should be confirmed on the model datasheet before circuit design; this guide does not assign a rating that is not in the published model specification. The documented OFS06A models above provide reference points for the low-power branch, but they do not replace the OFS06A-5 datasheet.
Power selection: use the nameplate, not the series headline
For early project screening, this guide uses a 1,500W to 3,850W range. That range is not a model rating. The documented OFS06A/B models in this article are 1,200W, 1,600W, 1,850W and 2,300W; the documented OFS06C outdoor models are 2,300W and 2,500W. A circuit designed for a 1,850W model should not be assumed to support a 2,300W or 2,500W model without recalculation. Conversely, a higher series ceiling does not mean every project needs it.
The correct process is to lock the model, read the nameplate, and have a qualified electrical professional confirm the supply, protection and installation requirements. The sauna room is a project item, not a plug-and-play appliance assumption. The buyer should record the selected model, its total power, the heater layout, the control model and the installation location in one specification sheet before ordering.
Heater configuration and AV1 control
The records distinguish far infrared heating plate from far infrared heating plate plus box. OFS06A-1 and OFS06A-3-1 list the plate; OFS06B-2, OFS06B-4, OFS06C-4 and OFS06C-3-2 list the plate plus box. The records do not provide comparative heat-up, penetration or efficiency test data, so this guide does not claim one layout outperforms the other. The buying decision is to confirm the intended heater layout, the panel positions and the control logic with the supplier.
AV1 control is common across the documented models. FM/Bluetooth/USB, two speakers, lamp and colorful light are also listed, which makes the guest-facing specification a control and ambience package rather than only a heating element. For hotel and spa use, the buyer should confirm how the control panel is accessed, where the audio and lighting controls are located, and whether the operating routine matches the facility's staff and guest instructions.
Materials, glass and installation conditions
Hemlock, aspen and red cedar are listed materials for the documented models. Tempered glass and a wood handle are also listed. This guide does not rank the wood species because the supplied product record does not include comparative performance test data. Wood choice should be confirmed as a specification and finish decision, not treated as an automatic performance guarantee.
Installation conditions are more explicit: the application record covers indoor or outdoor installation, high-temperature and variable climate conditions including sun exposure, rain and low temperature, and corrosion-resistant environments. Special requirements include heat-resistant and non-toxic materials, waterproof and moisture-proof construction, overheat protection, low EMF for infrared models, UV resistance for outdoor models, durable thermal insulation, and use with a control panel and safety thermometer. The OFS06C outdoor pentroof is a listed feature; the OFS06A/B records do not list a pentroof, so weatherproof suitability must be confirmed for the exact model and location.

Step-by-step specification path
- Define the project scenario and installation location. Write down whether the sauna room is for a hotel amenity area, guesthouse, wellness and commercial club or spa facility, and whether it is indoor or outdoor. Record sun exposure, rain, low temperature and corrosion exposure where relevant. This step prevents an indoor model from being treated as an outdoor weatherproof unit without written confirmation.
- Lock the exact model and read the nameplate. Compare OFS06A-5, OFS06B-2, OFS06B-4 and other candidate models only after the nameplate rating is available. Use the documented 1,200W, 1,600W, 1,850W, 2,300W and 2,500W reference points to start the electrical conversation, then replace them with the final model rating.
- Match the heater layout and AV1 control to the operating routine. Confirm whether the model uses a far infrared heating plate or a plate plus box. Confirm the AV1 control location and how FM/Bluetooth/USB, two speakers, lamp and colorful light are used by staff or guests. Do not assume a heater layout is interchangeable without supplier confirmation.
- Select wood, glass, lighting and audio as a coordinated finish. Choose from hemlock, aspen and red cedar according to the approved project finish, and confirm tempered glass, wood handle, lamp and colorful light. Keep the finish decision separate from the electrical and safety approval.
- Verify safety and installation requirements. Check heat-resistant and non-toxic materials, waterproof and moisture-proof construction, overheat protection, low EMF for infrared models, UV resistance for outdoor models, durable thermal insulation, control panel and safety thermometer. Confirm model-specific electrical safety documentation for the destination market where required.
- Confirm commercial terms and acceptance criteria. The supplier states OEM/ODM support, customization, 400 sets monthly capacity, MOQ 1 set, 30-40 days lead time, 100% test and remote guidance. Use these as contract and acceptance inputs, not as performance claims. Define the acceptance checklist around the model nameplate, heater layout, AV1 control, materials, glass, lighting and audio.
- Plan handover and after-sales. Confirm installation guidance, control instructions, safety thermometer use, maintenance expectations and remote after-sales support. Record the model, power, heater layout and installation condition in the handover file.
Scenario fit: hotel, guesthouse, wellness club and spa
Hotel and hospitality projects
For hotel and hospitality projects, the practical choice is the model that fits the electrical schedule and the guest-facing specification. OFS06B-2 at 1,850W and OFS06B-4 at 2,300W are documented B-series candidates; both list far infrared heating plate plus box, AV1 control, FM/Bluetooth/USB, two speakers, lamp and colorful light. Select between them only after the hotel's electrical capacity, installation location and room layout are confirmed. Do not specify OFS06B-4 merely because it has a higher documented power; a higher number is not automatically a better fit.
Guesthouse projects
Guesthouse projects often need a clear, compact specification rather than a large commercial package. OFS06A-3-1 at 1,600W and OFS06A-1 at 1,200W are documented low-power reference models in this set. OFS06A-5 should be specified after its individual nameplate is confirmed. The supplier states MOQ 1 set and 30-40 days lead time, which supports a single-unit project discussion; the buyer should still confirm the electrical schedule, installation condition and acceptance criteria before ordering.
Wellness and commercial club projects
Wellness and commercial club projects may require repeatable specifications across multiple units. The supplier states 400 sets monthly capacity, OEM/ODM support, customization and 100% test. A commercial spa case in Germany records 20 sets, including OFS06C-4 and OFS06B-5, with reported stable, safe operation, consistent heating and reliable performance. The case also lists low noise, energy efficiency and durable construction as highlights. Treat this as a documented project reference, not a guarantee for every installation.
Spa facility projects
Spa facilities should separate the guest experience specification from the technical approval. AV1 control, colorful light, FM/Bluetooth/USB and two speakers support the guest-facing side; power rating, heater layout, waterproof construction, overheat protection, low EMF verification for infrared models and control panel safety support the technical side. The documented OFS06C outdoor models add an outdoor pentroof, but the exact model must still match the installation location and local requirements.
Outdoor and weatherproof note
The secondary keyword outdoor weatherproof sauna room should be used carefully. In the supplied product records, the outdoor sauna room type and outdoor pentroof are listed on OFS06C-4 and OFS06C-3-2. The OFS06A/B records do not list an outdoor pentroof. Therefore, an OFS06A-5 or OFS06B model should not be presented as weatherproof unless the supplier confirms the exact installation condition in writing. For an outdoor spa or hotel terrace, confirm the outdoor model, foundation, drainage, UV exposure and corrosion requirements before approval.
Frequently asked questions
What should a hotel verify before specifying an OFS06 infrared sauna room?
A hotel should verify the installation location, indoor or outdoor exposure, the exact model nameplate, the electrical supply and protection, the heater layout, the AV1 control location, and the safety requirements. The application record lists heat-resistant and non-toxic materials, waterproof and moisture-proof construction, overheat protection, low EMF for infrared models, UV resistance for outdoor models, durable thermal insulation, control panel and safety thermometer as items to confirm. The compliance review should also separate room construction from the electrical or heater subsystem; EN 18164 and UL 60335-2-53 are examples of standards referenced in secondary industry reporting, but their applicability and model-specific documentation must be confirmed for the project.
Which OFS06B model fits a guesthouse with limited electrical capacity?
The documented OFS06B-2 is rated at 1,850W and OFS06B-4 at 2,300W, so OFS06B-2 is the lower documented B-series option in this guide. It lists far infrared heating plate plus box, AV1 control, FM/Bluetooth/USB, two speakers, lamp, colorful light, wood handle and tempered glass. The final choice should still be based on the guesthouse electrical schedule and the exact nameplate. The documented OFS06A-3-1 at 1,600W and OFS06A-1 at 1,200W are lower-power reference points, while OFS06A-5 requires its own datasheet confirmation.
What commercial terms affect an OFS06 sauna room project?
The supplier states MOQ 1 set, 400 sets monthly capacity, 30-40 days lead time, OEM/ODM support, customization and 100% test. The company also states 200+ employees, 9 engineers, a 50,000 m2 factory, 5,000 sets annual output and an 85% export ratio with markets including the USA, Australia, the EU and Germany. These terms should be confirmed in the quotation and contract for the specific model, finish and project quantity. The article does not quote a price because no model-specific OFS06 price is supplied.
How can a buyer validate an OFS06 sauna room before a larger order?
A buyer can use the stated MOQ of 1 set to discuss a single-unit project, then validate the exact model nameplate, heater layout, AV1 control, wood choice, tempered glass, lighting, audio and safety documents against the acceptance checklist. The supplier states 100% test and remote guidance, which should be written into the acceptance and handover process. The buyer should not approve a larger order until the single-unit specification, documents and installation conditions are confirmed.
What lead time and after-sales support apply, and where can I get the brochure?
The supplier states a 30-40 days lead time, 400 sets monthly capacity, 100% test and remote after-sales guidance. These are supplier-stated terms and should be confirmed for the selected OFS06 model and order quantity. For project planning, the OCEAN FUTURE sauna room brochure is available for download at the end of this guide.
Conclusion: specify the OFS06 model that fits the project record
The OFS06A-5 and OFS06B series should be specified by matching the documented nameplate, heater layout, AV1 control, materials and installation condition to the hotel, guesthouse, wellness club or spa scenario. The documented models provide useful reference points: 1,200W, 1,600W, 1,850W and 2,300W in the OFS06A/B records, and 2,300W and 2,500W in the OFS06C outdoor records. Use the 1,500W to 3,850W range only to start the electrical review, then lock the exact model.
Before approval, confirm the OFS06A-5 rating on its datasheet, confirm outdoor suitability for the exact model, and confirm purchasing terms such as MOQ 1 set, 30-40 days lead time, 400 sets monthly capacity, 100% test, OEM/ODM support and remote guidance. The result should be a sauna room specification that is traceable to the model record and suitable for the project's installation, compliance and guest-facing requirements.

Download the OCEAN FUTURE sauna room brochure for model and project planning: OCEAN FUTURE sauna room brochure.
Have Questions or Need More Details?
Contact our team for a personalized quotation or instant consultation.
Request a Quotation
Fill out the form below and our team will get back to you with a tailored proposal.
WhatsApp Direct Chat
Prefer to chat in real-time? Message us on WhatsApp for instant assistance & quick answers.
- Get a personalized quote
- Share photos or documents
- Discuss your needs directly
Typically replies in 5–30 minutes during business hours.
